A team led from Xi’an Jiaotong University, with co-authors at the École Polytechnique Fédérale de Lausanne and other institutions, has reported inverted perovskite cells that reached a certified power-conversion efficiency of 27.96% and a stabilised power output of 27.84%, in a Nature paper published on 18 November 2026. The same interface strategy, applied to monolithic perovskite-silicon tandems, produced a certified stabilised power output of 34.71%. Xi’an Jiaotong University, in a 19 November account of the work, said the 2,000-hour stability test was run on unencapsulated cells under nitrogen at about 45 °C. The results are from laboratory cells, not modules.
In brief
- The Nature paper, “Band-Edge-Extended Heterointerfaces for Perovskite Solar Cells and Tandems,” reports a certified 27.96% PCE and a 27.84% stabilised power output for inverted perovskite cells, and a certified 34.71% stabilised power output for a perovskite-silicon tandem.
- The devices use fully conjugated formamidinium interface molecules, including one the authors call BTFI, between the perovskite absorber and the C60 electron-transport layer.
- After 2,000 hours of continuous maximum-power-point tracking under 1-sun illumination, the cells retained over 95% of their initial efficiency. The university says that test used unencapsulated cells under nitrogen at about 45 °C.
Conjugated interface molecules sit between the perovskite and C60
The paper’s starting point is a familiar bottleneck. Further efficiency gains in perovskite cells, the authors write, are “increasingly limited by charge extraction and recombination at the interface between the perovskite absorber and the electron-transport layer.” Conventional ammonium-based modifiers can passivate defects, but many are only weakly electronically coupled to the perovskite surface and can add a barrier to electron extraction.
The team’s answer is a family of heteroatom-containing, fully conjugated formamidinium interfacial modulators, intended to extend the band edge at that heterointerface and keep a path open for electrons. In the university’s Chinese-language account, presented here in TSN’s translation, the authors designed molecules it names MeOTFI, TTFI and BTFI, and say BTFI can hybridise with the perovskite conduction-band edge and improve the energy-level alignment with C60. The Nature abstract reports the certified single-junction figures and says the corresponding devices “retained over 95% of their initial efficiency after 2000 h continuous maximum-power-point tracking under 1-sun irradiation (ISOS-L).”
Xi’an Jiaotong University is named as the first completing institution. Yuhang Liu of XJTU and Michael Grätzel of EPFL are among the corresponding authors, together with colleagues at Fudan University, CNPC’s tubular-goods institute, the National University of Singapore and Northwestern Polytechnical University, according to the university’s release.
Certified figures for the perovskite cells, and the 2,000-hour test
The Nature paper gives a certified PCE of 27.96% and a stabilised power output of 27.84% for the inverted cells, and a certified stabilised power output of 34.71% for the tandems. The university’s account, in TSN’s translation, adds that the tandem also achieved a certified scan efficiency of 34.74% and an open-circuit voltage of 2.009 volts, and that the scan and stabilised figures for the single-junction cells were close to one another.
The stability result needs the test conditions attached. The university says that, under nitrogen, at about 45 °C, and under continuous one-sun-equivalent illumination, unencapsulated BTFI-modified single-junction cells still held more than 95% of their initial efficiency after 2,000 hours of maximum-power-point tracking. Those are controlled laboratory conditions, not an outdoor, encapsulated-module trial.
The work sits in a line of recent engineering on perovskite cells rather than in a production announcement. A salt-mixture method for growing cleaner perovskite crystals tackled bulk crystal quality. Flexible perovskite modules that reached 20.2% at a commercial size moved the discussion onto larger-area modules. Ricoh’s plan to mass-produce inkjet-printed perovskite cells in Miyagi is a manufacturing commitment. This Nature paper is still a laboratory-cell result, with a new interface chemistry at its centre.
Certified laboratory cells are not a manufacturing claim
The certified percentages are the right numbers to report, and they should be reported with their boundaries. The single-junction 27.96% PCE and 27.84% stabilised output, and the tandem’s 34.71% certified stabilised output, come from the Nature paper. The 34.74% certified scan and 2.009-volt open-circuit voltage come from the university’s account of the same devices. Neither source presents those figures as a record, and they should not be billed as one.
The 2,000-hour retention figure is similarly bounded. “Over 95%” after continuous 1-sun tracking is a strong laboratory stability result, but the university is explicit that the cells were unencapsulated, held under nitrogen, and kept at about 45 °C. That is a much kinder environment than a rooftop module would face. It also means the result has not yet been shown on encapsulated modules, or at the areas associated with commercial production.
There is still a clear materials point. If a fully conjugated interface molecule can passivate the perovskite surface without blocking extraction into C60, that is a useful design idea, and the paper’s tandem result suggests the same chemistry can be tried on a wide-band-gap top cell. The next tests that would change the industrial reading are encapsulated-module lifetime, outdoor or damp-heat conditions, and yield at a larger area. Until those arrive, these perovskite cells remain a certified laboratory result, jointly signed from Xi’an and Lausanne, with a carefully described interface and a stability test that should be quoted in full.
Get TSN’s biggest tech stories, explained.
News and insights across AI, tech, crypto and cybersecurity. Every source linked. Unsubscribe anytime.
Get the newsletterRelated stories
- Salt Mixture Helps Grow Cleaner Perovskite Crystals for Solar Cells
- Flexible Perovskite Solar Modules Reach 20.2% at Commercial Size
- Ricoh to Mass-Produce Inkjet-Printed Perovskite Solar Cells in Miyagi
Sources
- Bitao Dong, Meijie Cui, Cong Chen et al., Band-Edge-Extended Heterointerfaces for Perovskite Solar Cells and Tandems, Nature, 18 November 2026
- Xi’an Jiaotong University, team reports progress on perovskite solar cells in Nature, 19 November 2026 (Chinese; figures and test conditions above follow TSN’s translation)
Follow @tsnmediahub on X for breaking AI news as it happens.
Follow on X


